Jet Plans:

Airliner
Designer: mcross
Designer Email: mcross at RCGroups
Specs: 14 inch wingspan, 16.5g AUW
Material Required: 2mm Depron
Downloads available:
Notes: Mike has created a nice looking airliner! I have created three graphic schemes for Mike's plane for download. If you create any others please feel free to submit them so they may be added. The drawings call for two fuselages to be cut out and bonded together for added strength. You may also consider using either a small carbon fiber ribbon along the bottom edge of the fuselage or balsa to do the same. This might reduce the AUW.

B2
Designer: Duane Cruz
Designer Email: Duane Cruz at RCGroups
Specs: 17 inch WS, 9g AUW
Material Required: 2mm Depron, CF for leading edge protection
Downloads available:
Notes: My version. 17" wingspan. Canopy made out of an AA Sport fuse cut and trimmed. It's super light and very fast. Carbon fiber strip is fastened to the leading edge. CG...battery as far forward dead center and the rx right up against it, just taped all down and sharpy'd black.

You might even want to think about increasing the overall size to 18-19". Sometimes it seemed to get away from me in turns and almost do a roll. The weight or lack there of had a lot to do with that. A lot of tapping around the turns.

The rudder is only a 1/2" X2" leftover from the cutout. Originally I creased the wingends creating some dehidral about 7 degrees up and then later put it back straight cause I put CF rod on the leading edge to stiffen it. As you can see, it's fast and when it hits.

BD-5J
Designer: dz1sfb
Designer Email: dz1sfb at RCGroups
Specs: 12.5 inch WS, 19.8 AUW
Material Required: 2,,3 and 6mm Depron
Downloads available:
Notes: dz1sfb has created a great BD-5! Here is what he has to say about the construction:

A little bit of solder in the nose (very little) and this bird is a delight. The CG is still around 33% of wing chord, but is now closer to 30%.

I had also added the carbon fiber rods to stiffen the nose, as cracks had developed from too many one point and wingtip landings.

Flying - very stable and lots of fun. Stall turns, loops, immelmans, and very loose barrel rolls. Turns have to be watched for getting in too much of a bank. This is remedied by pouring on the power and it will pull out of it.

All changes have been incorporated into revision C of the plans. Just watch the CG.

BD-5J 3mm Version
Designer: dz1sfb
Designer Email: dz1sfb at RCGroups
Specs: 12.5 inch WS, 19.8 AUW
Material Required: 3mm Depron
Downloads available:
Notes: Here is another great one from dz1sfb! Its a 3mm version of his great BD-5! Print the PDF with no scaling and your all set.......

BD-5J 3mm Version (Motor Top Mount)
Designer: dz1sfb
Designer Email: dz1sfb at RCGroups
Specs: 12.5 inch WS, 19.8 AUW
Material Required: 3mm Depron
Downloads available:
Notes: Here is another great one from dz1sfb! Its a 3mm version of his great BD-5 with the motors top mounted. Helps to combat the wind! Print the PDF with no scaling and your all set.......

Cutlass
Designer: nitrostar
Designer Email: nitrostar at RCGroups
Specs: 16 to 18 grams AUW
Material Required: 3mm Depron
Downloads available:
Notes:

Cutty
Designer: relaxr
Designer Email: relaxr at RCGroups
Specs: 10 inch Wingspan
Material Required: 2mm Depron
Downloads available:
Notes: Designed from a prototype the author dissected. Cool plane.

Eurofighter
Designer: streff
Designer Email: streff at RCGroups
Specs: 10 inch wingspan
Material Required: 2 - 2.5 mm Depron
Downloads available:
Notes: Tape together the PDF at the edges of the paper, don't overlap, or shrink to fit page when printing. The author may soon be kitting this model. Nice video.

F-15
Designer: Megabyte-2
Designer Email: Megabyte-2 at RCGroups
Specs: 7.5 inch wingspan, 10.57g AUW
Material Required: 2mm Depron
Downloads available:
Notes: This F 15 is fast. Flying just below 1/2 throttle. Designed for a 90ma Lipo.

F18
Designer: Doug Hinkel
Designer Email: Doug Hinkel's email
Specs: 9 inch WS
Material Required: 2 or 3mm Depron
Downloads available:
Notes: Please check the pictures on this one along with the build instructions that Doug has put together. Here are some additional notes from Doug: "You may note the pictures show the profile type and full body. Same plans and the body width is two 5/8 wide formers 1" in front of the wing and at the balance point in the rear. The canopy was added after boxing the fuselage sanding. Flies ok with stock x-twin motors but great with 7mm orange motors. Enjoy! Doug "

F22 Raptor
Designer: Claes Meijers - ojonod build (Jonas)
Designer Email: ojonod at RCGroups
Specs: 180mm WS, 15g AUW
Material Required: 2mm Depron
Downloads available:
Notes: This raptor is made from Claes Meijers F22 Raptor, the original plans can be found here
http://web.telia.com
I just printed the plan on a A4 paper and it was just right size for the X-Twin setup. Check out Claes site for other interesting stuff!

FW Ta283 Plan
Designer: FidlerEd
Designer Email: FidlerEd at RCGroups
Specs: Unknown
Material Required: 2mm Depron
Downloads available:
Notes: Design proposed by author. Has yet to fly.

Harpy Cat
Designer: Chara
Designer Email: Chara at RCGroups
Specs: Scaled down to 12 inches from original print
Material Required: Unknown
Downloads available:
Notes: Information is sketchy on this design. The author never posted if adapting to AA gear was sucessful or not.

Lockheed ER-2 High Altitude Research Aircraft
Designer: sr71fan
Designer Email: sr71fan at RCGroups
Specs: 18inch WS 15.4g AUW
Material Required: 2mm Depron
Downloads available:
Notes: For the plan, scale to 250% cut out, make several copies, tape together and trace on the foam.

ME163 Kraftei
Designer: Christian Bürger
Designer Email: Author home page
Specs: Pylon Racing Jet
Material Required: 2 or 3mm Selitron (Depron)
Downloads available:
Notes: Here are Christian Bürger notes on this design: "..we made coloured plans in several designs. You can print them on light paper, put them onto the Depron and Selitron and have a nice flyer without need to draw the design by yourself. There are four different designs. Unfortunally we took very heavy paper for the prototype, which was only flyable with a full battery. If you don't have light paper it is better to reduce the plan by 10% to make it lighter" Thanks again Christian! Note: The BMP link contains the fourth PDF design.

ME262
Designer: Relaxr
Designer Email: Relaxr at RCGroups
Specs: Unknown
Material Required: 2mm Depron
Downloads available:
Notes: The Me 262 plan - a really nice flyer, if trimmed and bend correctly. It really flies on its foil, needs just short stick inputs, turns close, climbs well, allows slow circles and eights and also fast acrobatics (be high enough ). I made new pics as a help for its trims, which are essential. Before those it was just an avarage flyer. Shape it !
Sorry for the sketched plan - I dont have enough time for proff. graphics - but this here allows you to copy it.
If something remains unclear - feel free to ask . Good success.

SU-37
Designer: Astrodavid
Designer Email: Astrodavid at RCGroups
Specs: 12.5 inch WS,27g AUW
Material Required: Depron 2 or 3 mm
Downloads available:
Notes: For those interested in the SU-37, here is a profile SU-37 that I built with AeroAce/X-Twin components. I used 2mm and 3mm Depron. A nice flyer, I built it with a wingspan of 12.5 inches (32 cm) and final weight of 27 grams. It flys well in very calm winds or inside ... I would recommend slightly reducing the wingspan to 12 inches and therefore the weight to 25 grams; this will give better flying performance.

Additional build notes: The pager motors on all my 16 inch wingspan profile models are located 4 inches off the centerline (total of 8 inches apart). This seems to provide good turns.

Selfo Jets
Designer: Selfo Jets
Designer Email: Selfo -for archival use only
Specs: 12 inch Wingspan
Material Required: 2mm Depron
Downloads available:
Notes: Selfo use to create some really unique craft. Unfortunately his site is now gone, so these designs have been brought back for your enjoyment!

SkyRay
Designer: FidlerEd
Designer Email: FidlerEd at RCGroups
Specs: 10 inch Wingspan, 18 grams AUW
Material Required: 2mm Depron
Downloads available:
Notes: This airframe has an airfoil to assist in flight. The downloadable graphic can be printed on mat tracing paper and glued to the airframe.

Strykerish
Designer: MiseryQ
Designer Email: MiseryQ at RCGroups
Specs: Two designs, 9.5 and 12 inch Wingspan
Material Required: 3mm CellFoam88
Downloads available:
Notes: The 9.5" was a little squirmish and needed almost full throttle to stay flying so the larger version should have more lift. Authors note: Both models took full throttle to stay in the air, so you may have to do some work with this design. 2mm Dupron may help.

T38 Talon
Designer: dz1sfb
Designer Email: dz1sfb at RCGroups
Specs: 9.5 inch WS, 17.9g AUW
Material Required: 3mm Depron
Downloads available:
Notes: Norhtrop T-38 Talon
9.5" wingspan
16.375" length
17.9 grams - AUW
Plan view and side view profiles
Panel line detailing
Intended color scheme is USAF Thunderbirds

This one flew right off the board. One tip I learned here was to find the CG first by testing without motors, batt, and RX. This gives the lightest wing loading (less potential damage), and lower stress (on me).


The Alleycat
Designer: Racerx208
Designer Email: Racerx208 at RCGroups
Specs: 12 inch Wingspan, 17 grams AUW
Material Required: 2mm Depron
Downloads available:
Notes: A smooth flying jet....

The Alleycat (3mm)
Designer: nitrostar
Designer Email: nitrostar at RCGroups
Specs: 11.5 inch Wingspan
Material Required: 3mm Depron
Downloads available:
Notes: ....like the 2mm version, a really smooth flyer....

The Alleycat (3mm, 10 inch)
Designer: nitrostar
Designer Email: nitrostar at RCGroups
Specs: 10 inch Wingspan
Material Required: 3mm Depron
Downloads available:
Notes: 10 inch version of Alleycat.

The Lite-Jet
Designer: Racerx208
Designer Email: Racerx208 at RCGroups
Specs: 12 inch Wingspan, 15.8 grams AUW
Material Required: 2mm Depron
Downloads available:
Notes: Available soon.

Vulcan
Designer: relaxr
Designer Email: relaxr at RCGroups
Specs: AUW less than 19 grams
Material Required: 2mm Depron
Downloads available:
Notes: Nice looking Vulcan bomber